收藏本站
NCL30001
di
V RCOMP +
@ T @ R CS @ A HF
N S L P @ 102.38k
R CS +
@
t on
V ref(PWM) + V RCOMP @
) V INST
R RCOMP + @ (eq. 24)
3.8 * 5.333 @ I PK @ R CS
3.8
R CS +
out @ t on
P
HF
(eq. 20)
dt primary
(eq. 21)
N P T @ A HF @ V out @ R RCOMP
At low line and full load, the output of the ac error
amplifier output is nearly saturated in a low state. While the
ac error amplifier output is saturated, I ACEA is zero and does
not contribute to the voltage across the internal 21.33 k W
resistor on the PWM comparator non-inverting input. In this
operation mode, the voltage across the 21.33 k W resistor is
determined solely by the ramp compensation and the
instantaneous switch current as given by Equation 22.
(eq. 22)
T
The voltage reference of the PWM Comparator,
V REF(PWM) , is 4 V. For these calculations, 3.8 V is used to
provide some margin. The maximum instantaneous switch
current voltage contribution, V INST , is given by
Equation 23.
V INST + I PK @ R CS @ A HF (eq. 23)
Substituting Equation 23 in Equation 22, setting
V REF(PWM) at 3.8 V (provides margin) and solving for
R RCOMP, Equation 24 is obtained.
102.38k t on
T
Replacing Equation 24 in Equation 21 we obtain:
(eq. 25)
N A @ V
N @ L ) 5.333 I PK
S P
latch is Set dominant which means that if both R and S are
high the S signal will dominate and Q will be high, which
will hold the power switch off.
The NCL30001 uses a pulse width modulation scheme
based on a fixed frequency oscillator. The oscillator
generates a voltage ramp as well as a pulse in sync with the
falling edge of the ramp. The pulse is an input to the PWM
Logic and Driver block. While the oscillator pulse is present,
the latch is reset, and the output drive is in its low state. On
the falling edge of the pulse, the DRV goes high and the
power switch begins conduction.
The instantaneous inductor current is summed with a
current proportional to the ac error amplifier output voltage.
This complex waveform is compared to the 4 V reference
signal on the PWM comparator inverting input. When the
signal at the non-inverting input to the PWM comparator
exceeds 4 V, the output of the PWM comparator toggles to
a high state which drives the Set input of the latch and turns
the power switch off until the next clock cycle.
Brown ? Out
The NCL30001 incorporates a brown ? out detection
circuit to prevent the controller operate at low ac line
voltages and reduce stress in power components. A scaled
version of the rectified line voltage is applied to the VFF Pin
by means of a resistor divider. This voltage is used by the
brown out detector.
A brown ? out condition exists if the feedforward voltage
is below the brown ? out exit threshold, V BO(high) , typically
0.45 V. The brown ? out detector has 175 mV hysteresis. The
controller is enabled once V FF is above 0.63 V and V CC
reaches V CC(on) . Figure 59 shows the relationship between
the brown ? out, V CC and DRV signals.
PWM Logic
The PWM and logic circuits are comprised of a PWM
comparator, an RS flip-flop (latch) and an OR gate. The
http://onsemi.com
28
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
NCP102MBGEVB EVAL BOARD FOR NCP102MBG
NCP1081SPCGEVB EVAL BOARD FOR NCP1081SPCG
NCP1083QBCGEVB EVAL BOARD FOR NCP1083QBCG
NCP1083WIRGEVB EVAL BOARD FOR NCP1083WIRG
NCP1521BEVB EVAL BOARD FOR NCP1521B
NCP1523BGEVB EVAL BOARD FOR NCP1523BG
NCP1605FORWGEVB EVAL BOARD FOR NCP1605FORWG
NCP1840Q8A6MNTWG IC LED DRIVER 12CH PROGR 20QFN
相关代理商/技术参数
NCL30001DR2G-CUT TAPE 制造商:ON 功能描述:NCL30001 Series 11.3 V Isolated Step-Down Single Stage Power Factor - SOIC-16
NCL30001LEDGEVB 功能描述:LED 照明开发工具 Programmers Development RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装:
NCL30002 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Power Factor Corrected Buck LED Driver
NCL30002DIM1GEVB 制造商:ON Semiconductor 功能描述:120V DIMMABLE HPF BUCK - Bulk
NCL30002DIM2GEVB 制造商:ON Semiconductor 功能描述:230V DIMMABLE HPF BUCK - Bulk
NCL30002DR2G 功能描述:LED照明驱动器 Power Factor Offline Buck LED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
NCL30002LED1GEVB 制造商:ON Semiconductor 功能描述:90-135VAC HPF BUCK DRIVER - Bulk
NCL30002LED2GEVB 制造商:ON Semiconductor 功能描述:220/240VAC HPF BUCK DRIVE - Bulk